? epcos ag 2011. reproduction, publication and dissemination of this data sheet, enclosures hereto and the information contained therein without epcos prior express consent is prohibited. saw components saw if filter gsm base station series/type: ordering code: b5233 B39141B5233H810 date: version: jun 30, 2011 2.0
2 jun 30, 2011 b5233 138.2 mhz please read cautions and warnings and important notes at the end of this document. saw components saw if filter data sheet application n low-loss if filter for gsm applications n usable passband 35 mhz n balanced operation features n package size 7.0 x 5.0 x 1.33 mm 3 n package code qcc12e n rohs compatible n approx. weight 0.25 g n ceramic package for s urface m ount t echnology ( smt ) n ni, gold-plated terminals n e lectrostatic s ensitive d evice ( esd ) n filter surface passivated n moisture sensitivity level 1 pin configuration n 10, 12 input n 4, 6 output n 1,5,7,11 case ground n 2,3,8,9 to be grounded 1,5,7,11
3 jun 30, 2011 b5233 138.2 mhz saw components saw if filter data sheet please read cautions and warnings and important notes at the end of this document. characteristics operating temperature range: t = C40 to 85 ?c terminating source impedance: z s = 200 w balanced and matching network terminating load impedance: z l = 200 w balanced and matching network min. typ. @ 25 ?c max. nominal frequency f n 138.2 mhz minimum insertion attenuation (including matching network) a min 10.4 12 db passband width a rel < 1.2 db b 1.2db 35.0 41 mhz amplitude ripple (p-p) da f n 17.6 mhz 0.7 1.4 db group delay ripple (p-p) dt f n 17.6 mhz 30 100 ns relative attenuation (relative to a min ) a rel 28.00 mhz ... 64.00 mhz 40 58 db 212.0 mhz ... 464.0 mhz 40 44 db 464.0 mhz ... 3000 mhz 45 60 db average group delay t mean f n 17.6 mhz 0.540 1.0 m s temperature coefficient of frequency tc f -75 ppm/k
4 jun 30, 2011 b5233 138.2 mhz please read cautions and warnings and important notes at the end of this document. saw components saw if filter data sheet matching network to 200 w balanced input - 200 w balanced output (element values depend upon pcb properties and layout) maximum ratings operable temperature range t C40/+85 ?c storage temperature range t stg C55/+125 ?c dc voltage v dc 0 v input power at 120.6-155.8 mhz p in 20 dbm cw 200 w ls1 = 100 nh lp1 = 120 nh ls2 = 47 nh lp2 = 120 nh ls1 ls1 lp1 ls2 ls2 lp2 200 w
5 jun 30, 2011 b5233 138.2 mhz saw components saw if filter data sheet please read cautions and warnings and important notes at the end of this document. transfer function (s21, wideband, normalised) transfer function (s21, narrowband, normalised)
6 jun 30, 2011 b5233 138.2 mhz please read cautions and warnings and important notes at the end of this document. saw components saw if filter data sheet references type b5233 ordering code B39141B5233H810 marking and package c61157-a7-a103 packaging f61074-v8170-z000 date codes l_1126 s-parameters b5233_nb.s2p; b5233_wb.s2p soldering profile s_6001 rohs compatible defined as compatible with the following documents: "directive 2002/95/ec of the european parliament and of the council of 27 january 2003 on the restriction of the use of certain hazardous substances in electrical and electronic equipment. 2005/618/ec from april 18th, 2005, amending directive 2002/95/ec of the european parliament and of the council for the purposes of establishing the maxi- mum concentration values for certain hazardous substances in electrical and electronic equipment." matching coils see inductor pdf-catalog http:// www .tdk.co.jp/tefe02/coil.htm#aname1 and data library for circuit simulation http://www.tdk.co.jp/etvcl/index.htm for further information please contact your local epcos sales office or visit our webpage at w ww.epcos.com . published by epcos ag systems, acoustics, waves business group p.o. box 80 17 09, 81617 munich, germany ? epcos ag 2011. this brochure replaces the previous edition. for questions on technology, prices and delivery please contact the sales offices of epcos ag or t he international representatives. due to technical requirements components may contain dangerous substances. for information on t he type in question please also contact one of our sales offices.
7 jun 30, 2011 important notes the following applies to all products named in this publication: 1. some parts of this publication contain statements about the suitability of our products fo r certain areas of application . these statements are based on our knowledge of typical requirements that are often placed on our products in the areas of application concerned. we nevertheless expressly point out that such statements cannot be regarded as binding statements about the suitability of our products for a particular customer application. as a rule, epcos is either unfamiliar with individual customer applications or less familia r with them than the customers themselves. for these reasons, it is always ultimatel y incumbent on the customer to check and decide whether an epcos product with the properties described in the product speci?cation is suitable for use in a particular custome r application. 2. we also point out that in individual cases, a malfunction of electronic components o r failure before the end of their usual service life cannot be completely ruled out in the current state of the art, even if they are operated as speci?ed. in customer applications requiring a very high level of operational safety and especially in customer applications in which the malfunction or failure of an electronic component could endanger human life o r health (e.g. in accident prevention or life-saving systems), it must therefore be ensured b y means of suitable design of the customer application or other action taken by the custome r (e.g. installation of protective circuitry or redundancy) that no injury or damage is sustained b y third parties in the event of malfunction or failure of an electronic component. 3. the warnings, cautions and product-speci?c notes must be observed. 4. in order to satisfy certain technical requirements, some of the products described in this publication may contain substances subject to restrictions in certain jurisdictions (e.g. because they are classed as hazardous) . useful information on this will be found in ou r material data sheets on the internet (www.epcos.com/material). should you have any more detailed questions, please contact our sales of?ces. 5. we constantly strive to improve our products. consequently, the products described in this publication may change from time to time . the same is true of the corresponding produc t speci?cations. please check therefore to what extent product descriptions and speci?cations contained in this publication are still applicable before or when you place an order. we also reserve the right to discontinue production and delivery of products . conse- quently, we cannot guarantee that all products named in this publication will always be available. the aforementioned does not apply in the case of individual agreements deviating from the foregoing for customer-speci?c products. 6. unless otherwise agreed in individual contracts, all orders are subject to the current version of the general terms of delivery for products and services in the electrical industry published by the german electrical and electronics industry association (zvei) . 7. the trade names epcos, baoke, alu-x, ceradiode, csmp, cssp, ctvs, deltacap, digisimic, dssp, formfit, miniblue, minicell, mkd, mkk, mlsc, motorcap, pcc, phasecap, phasecube, phasemod, phicap, siferrit, sifi, sikorel, silvercap, simdad, simic, simid, sineformer, siov, sip5d, sip5k, thermofuse, windcap are trademarks registered or pending in europe and in other countries. further information will be found on the internet at www.epcos.com/trademarks.
|
